Classification of wallboard materials

Jun 10, 2022

Mixed structure

Mixed structure houses with brick or block walls and reinforced concrete or prestressed concrete floors. Because of its simple construction and low cost, it is the most widely used structural form; However, the self weight is large and the anti-seismic performance of the wall is poor. In order to improve its anti-seismic performance, reinforced concrete structural columns, also known as anti-seismic columns, are added at the junction of internal and external walls and the corners of external walls. The structural column is connected with the ring beam of the building and roof to improve the integrity, strength and deformation capacity of the building. If the wall is built with hollow blocks, steel bars can be inserted into the block holes through the upper and lower parts, and concrete is poured into the holes to form reinforced concrete columns, so as to increase the earthquake resistance of the house.

Fabricated large plate structure

Prefabricated large slab structure is a building structure assembled with precast concrete wall panels and floor slabs. It is a highly industrialized building structure system developed after the Second World War. The main advantages are that it can carry out commercialized production, high site construction efficiency, low labor intensity, light self weight, and better structural strength and deformation capacity than the hybrid structure. However, due to the high cost, large-scale transportation and hoisting machinery is required, and the plane layout is not flexible enough. Wall panels are divided into interior wall panels and exterior wall panels according to building functions. The inner wall panel is mainly used as a load-bearing component and is made of a single material. The exterior wall panels are generally non load-bearing wall panels, which have the functions of heat preservation, heat insulation and waterproof. The structure is relatively complex. Some of them are made of a variety of materials. Wall panels are divided into concrete hollow wall panels, solid wall panels, lightweight aggregate concrete wall panels, industrial waste concrete wall panels, vibrating brick wall panels, etc. according to the different materials used. The connection structure of prefabricated large plate structure is the key to whether the house can give full play to its strength, ensure the necessary stiffness and spatial overall performance. How to strengthen the connection:

① Weld the rebar protruding from the upper and lower wall panels and the adjacent floor;

② The four sides of the wall and floor slab are provided with slots to increase the ability of the joint to transmit shear force;

③ The joint shall be cast into a whole with concrete. It is also useful to add vertical prestress in the wall to connect the floor and wallboard as a whole.

Internal force calculation: strength calculation under vertical and horizontal loads shall be made for wallboards, floors and their joints. Internal force analysis of the wall: under the action of vertical load and out of plane horizontal load, the wall shall be calculated according to the vertical members supported on the roof, floor and foundation with fixed hinges at both ends; When the horizontal load is applied in the plane, the wall shall be calculated as a vertical cantilever structure embedded in the foundation, and the influence of the joint work of the longitudinal and transverse walls and the size of the wall opening shall be considered at the same time.

Cast in situ wallboard structure

Cast in place wallboard structure the wall is cast in place with concrete, and the floor is a prefabricated or cast-in-place house structure. The main advantage is good seismic performance. Compared with the mixed structure, the amount of wall plastering is greatly reduced, the labor intensity is reduced, and the amount of labor is less; Compared with the fabricated large plate structure, the construction is simple, so it has developed rapidly, and has become one of the main structural forms of multi-storey and high-rise residential buildings in China's earthquake areas. The wall materials and construction methods of cast-in-place wallboard structure can be divided into all cast-in-place concrete for internal and external walls and cast-in-place concrete for horizontal walls and internal and vertical walls. The external walls adopt precast large plates (referred to as internal casting and external hanging) or bricks and blocks (referred to as internal casting and external masonry). The cast-in-place walls can be constructed by using stereotyped formwork (large formwork, combined formwork, tunnel formwork) or by using slip form and formwork lifting methods. The floor slab shall be cast-in-place concrete floor slab, prefabricated strip slab or whole slab, and the floor slab shall be made into continuous slab to improve the integrity of the house. For the wall panel structure of internal and external masonry, the external wall shall be built first, and then the concrete internal wall shall be poured to ensure the good combination of internal and external walls.

Internal force calculation: under the action of vertical load, the internal force is distributed according to the area ratio of the cross-section of the vertical and horizontal walls. When the lateral horizontal force is applied, a part of the outer longitudinal wall can be used as the effective flange of the horizontal wall, and the calculation graph can be simplified as a frame. Each wall limb of the horizontal wall is used as a frame column, the coupling beam of the horizontal wall is used as a frame beam, and the floor is used as a hinged connecting rod. The lateral horizontal force is calculated according to the joint work of all the horizontal walls. When the longitudinal horizontal force acts, the transverse wall takes part in the work, and the structure is composed of longitudinal and transverse walls along the longitudinal direction. The calculation graph can be simplified as a composite frame composed of internal and external walls, the coupling beam of the external longitudinal wall is used as a frame beam, and the wall limb of the longitudinal wall and the transverse wall form a frame column. If the internal and external wall materials are different, the external wall thickness shall be converted according to the ratio of the elastic modulus of the external and internal wall materials.

You Might Also Like